Perbandingan waste besi tulangan pelaksanaan proyek konstruksi dengan perhitungan bar bending schedule (studi kasus: proyek pembangunan M&G Villa, Jalan Pantai Berawa, Canggu, Kecamatan Kuta Utara, Kabupaten Badung – Bali)

Authors

  • Ida Ayu Putu Sri Mahapatni Program Studi Teknik Sipil, Faultas Teknik, Universitas Hindu Indonesia, Denpasar, Bali, Indonesia
  • I Wayan Artana Program Studi Teknik Sipil, Faultas Teknik, Universitas Hindu Indonesia, Denpasar, Bali, Indonesia
  • Made Novia Indriani Program Studi Teknik Sipil, Faultas Teknik, Universitas Hindu Indonesia, Denpasar, Bali, Indonesia
  • Ni Made Yuyun Praptaningsih Program Studi Teknik Sipil, Faultas Teknik, Universitas Hindu Indonesia, Denpasar, Bali, Indonesia

DOI:

https://doi.org/10.22225/pd.13.2.10672.199-203

Keywords:

bar bending schedule, construction projects, material, villa, waste

Abstract

Excess construction materials or waste is a waste that has an impact on the construction project budget. Planning is needed in the use of construction materials, especially reinforcing steel materials, to minimize this waste material that occurs. The aim of this research is to obtain a comparison waste reinforcing iron in project implementation with planned calculations using bar bending schedule. This research was carried out on the M&G Villa structure which has a first floor area of 187 m2 and a second floor of 218 m2 located on Pantai Berawa Road, Canggu. The type of research used is quantitative research. Data processing using bar bending schedule calculations. Based on the results of the calculations that have been carried out, it is obtained waste material using calculation planning bar bending schedule amounting to 9.72% or weighing 1,331.39 kg of the total iron requirements, meanwhile waste The material that has been implemented in construction projects amounts to 13.41% or weighing 2,215.43 kg of the total requirement for reinforcing iron. The results of this calculation show waste with planning bar bending schedule can minimize waste reinforcing iron is 3.69% of waste implementation of the M&G Villa construction project.

References

Abidah, G. (2023). Perbandingan Kombinasi Pemotongan Pembesian dengan Metode Manual Bar Bending Schedule dan Tekla Structures. Jurnal Teknik ITS, 12, D90–D95. http://dx.doi.org/10.12962/j23373539.v12i2.112943

Arifin, D., Saputra, A. J., & Savitri, A. (2022). Efektifitas Pembesian pada Proyek Panbill Mall menggunakan Bar Bending Schedule SNI-2847-2019, BS-8666-2005, dan Linear Programming. Jurnal Manajemen Teknologi & Teknik Sipil, 5(1). https://doi.org/10.30737/jurmateks.v5i1.2588

Badan Standardisasi Nasional. (2019). Persyaratan Beton Struktural Untuk Bangunan Gedung 1.

Benidikta, P. (2018). Kajian Terhadap Limbah Konstruksi Pada Proyek Pembangunan Hotel @Hom Di Yogyakarta.

BPS Statistics Indonesia. (2022). Indikator Konstruksi Triwulanan III 2022.

Ebtha Yuni, N. K. S., Yuliana, N. P. I., & Sudiarta, I. K. (2023). Analisa waste material besi dalam upaya pengendalian sisa material konstruksi. Jurnal Teknik Sipil Terapan, 5(1). https://doi.org/10.47600/jtst.v5i1.561

Hartono, W., Utami, H., & Sunarmasto. (2015). Rancangan Program Pengerjaan Bar Bending Schedule Penulangan Pile Cap Dan Kolom Bawah Dengan Visual Basic 6.0. E-Jurnal Matriks Teknik Sipil, 3(2). https://doi.org/10.20961/mateksi.v3i2.37193

Kurniawan, D. (2023). Optimasi Perhitungan Kebutuhan Tulangan Dan Tulangan Sisa (Waste) Shear Wall Menggunakan Software Cutting Optimization Pro Pada Proyek Pembangunan Gedung Mrt Jakarta. 610–617.

Larasaty, E. (2023). Perhitungan Kebutuhan, Sisa, Dan Biaya Tulangan Pekerjaan Struktur Asrama Siswa Terpadu Mtsn 2 Medan. Majalah Iptek Politeknik Negeri Medan Polimedia, 25(1). https://doi.org/10.51510/polimedia.v25i1.1372

Mahapatni, I. A. P. S., & Juliana, I. K. I. (2022). Analisis Waste Level Dan Waste Cost Bekisting Dan Pembesian Pada Pekerjaan Struktur Proyek Konstruksi (Studi Kasus: Pembangunan Gedung Smpn 4 Sukawati). Jurnal Teknik Gradien, 17(1). https://doi.org/10.32795/widyateknik.v17i01.2977

Perdana, A. S., Indrayadi, M., & Pratiwi, R. (2020). Identifikasi Construction Material Waste Pada Proyek Pembangunan Gedung (Studi Kasus : Rumah Jabatan Rektor Untan Pontianak).

Permana, I. (2021). Optimasi Kebutuhan Tulangan Pada Balok Menggunakan Program Linier Metode Simplex Dan Building Information Modeling (Bim) (Optimization Beam Reinforcement Using Linear Program Simplex Method And Building Information Modeling).

Riyanto, M. S. D. (2023). Analisis Perbandingan Waste Metode Distribusi Dengan Software Cutting Optimization Pro Pada Pekerjaan Penulangan Pilecap (Studi Kasus :Proyek Xyz Semarang). 74–81.

Sinipat, L., & Beatrix, M. (2023). Analisis Kebutuhan Material Besi Tulangan Pada Struktur Beton Bertulang Dengan Metode Bar Bending Schedule Pada Proyek Pembangunan Sekolah Cita Hati Surabaya. Jurnal Ilmiah Teknik Dan Manajemen Industri, 3(1), 668–701. https://doi.org/10.46306/tgc.v3i1

Sulistio, H., & Wati, M. (2021). Analisis Faktor Kerugian Waste Material Besi Beton Gedung Bertingkat. Jurnal Muara Sains, Teknologi, Kedokteran Dan Ilmu Kesehatan, 5(1). https://doi.org/10.24912/jmstkik.v5i1.10120

Wiguna, I. P. A. (2009). Analisis Penanganan Material Waste Pada Proyek Perumahan Di Surabaya. Seminar Nasional Aplikasi Teknologi Prasarana Wilayah.

Yuni, N. K. S. E., Yuliana, N. P. I., Sudiarta, I. K., Proyek Konstruksi, M., Sipil, T., & Negeri Bali, P. (2023). Analisis Waste Material Besi dalam Upaya Pengendalian Sisa Material Konstruksi. In JTST (Vol. 5, Issue 1). http://jurnal.polimdo.ac.id/

Downloads

Published

2024-12-30

Issue

Vol. 13 No. 2 (2024)

Section

Articles

License

Authors who publish with this journal agree to the following terms:

1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution-ShareAlike 4.0 International (CC BY-SA 4.0) that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.

2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.

3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).