The design of the flat slab system with drop panel in the Sukawati market building
Abstract
Sukawati Market Building has 4 floors and 1 basement with a total building area of 1136.16 m2. It was designed to use a flat slab structure system with the addition of drop panels that maintained the height or story clearance while reducing total building height by eliminating the interior beams. The structure was designed follow the Indonesian Standard for reinforced concrete building design guideline and assessed through finite element simulation. The shear capacity of the flat slab was determined by the strength of the concrete and its dimensions. The reinforcing bar of flat slabs with drop panels is determined in the same way as the reinforcing bar of concrete slabs. Based on the results, the design efficiently resists the forces demand while meeting the deflection requirement, reflecting the structure system's safety and serviceability. The structure system also maintains the total height of the building in order to comply with local high-limit regulation.
References
I. N. Sinarta and I. M. B. Pinandika, “Comparison Of Pushover Method And Direct Displacement Method In Earthquake Load Analysis With Performance-Based Design Concepts,†Ukarst Univ. Kadiri Ris. Tek. Sipil, vol. 4, no. 2, 2020.
I. W. M. Andreasnata, I. N. Sinarta, N. K. Armaeni, and I. P. E. Sarassantika, “Column structure strengthening with FRP (Fiber Reinforced Polymer) due to story addition,†J. Infrastrcuture Plan. Engfineering, vol. 1, no. 1, pp. 38–45, 2022.
I. N. Sinarta and I. W. A. Basoka, “Safety factor analysis of landslides hazard as a result of rain condition infiltration on Buyan-Beratan Ancient Mountain,†J. Phys. Conf. Ser., vol. 1402, no. 2, 2019.
I. P. Ellsa Sarassantika, “Perencanaan Gedung the Samator Superblock dengan Elemen structure beton pratekan parsial paska tarik,†Institut Teknologi Sepuluh Nopember, 2015.
D. Evlin and I. N. Sinarta, “Prestressed beam system due to the addition of a long-span beam in building infrastructure,†J. Infrastruct. Plan. Eng., vol. 1, no. 1, pp. 27–32, 2022.
C. B. Casita, I. P. E. Sarassantika, and R. Sulaksitaningrum, “Behaviour of Rectangular Concrete Filled Tubes and Circular Concrete Filled Tubes under Axial Load,†J. Appl. Sci. Manag. Eng. Technol., vol. 1, no. 1, pp. 14–20, 2020.
Peraturan Daerah Provinsi Bali Nomor 16 Tahun 2009: Rencana Tata Ruang Wilayah Provinsi Bali. 2009.
S. Borkar, K. Dabhekar, I. Khedikar, and S. Jaju, “Analysis of Flat Slab Structures in Comparison with Conventional Slab Structures,†IOP Conf. Ser. Earth Environ. Sci., vol. 822, no. 1, 2021.
A. Rahman Asy-Syifa and dan Johannes Tarigan, “Analisa Flat Slab Dengan Memakai Drop Panel Kolom Persegi Dengan Variasi Pembebanan Life Load,†J. Tek. Sipil USU, vol. 1, no. 1, 2017.
D. Z. Yankelevsky, Y. S. Karinski, A. Brodsky, and V. R. Feldgun, “Dynamic punching shear of impacting RC flat slabs with drop panels,†Eng. Fail. Anal., vol. 129, no. April, p. 105682, 2021.
Badan Stadandarisasi Nasional-BSN, SNI 2847-2019 : Persyaratan beton struktural untuk bangunan gedung dan penjelasan, no. 8. 2019.
Computer and Structures.Inc (CSI), “ETABS.†Computer and Structures, Inc (CSI), 2013.
ATKINS, “Manual for Analysis & Design Using ETABS.†.
2020 SNI 1727, “Beban desain minimum dan Kriteria terkait untuk bangunan gedung dan struktur lain 1727:2020,†Badan Standarisasi Nas. 17272020, no. 8, pp. 1–336, 2020.
Badan Standardisasi Nasional, “Tata Cara Perencanaan Ketahanan Gempa Untuk Struktur Bangunan Gedung dan Non Gedung,†Sni 17262019, no. 8, p. 254, 2019.
Abstract viewed = 195 times
PDF downloaded = 462 times
